Javascript required
Skip to content Skip to sidebar Skip to footer
Home / Easy Way to Press a Watch Back on

Easy Way to Press a Watch Back on

Download Article

Download Article

When you don't have the specialized tools to remove a watch backing, you may not know how to replace a battery or fix a broken watch. But you don't need to buy expensive tools to pry off your watch's backing. In many cases, specific household items will do. Depending on your watch, you may be able to pry off the backing with something as simple as your thumbnail, a razor blade, a rubber ball, or a pair of scissors.

  1. 1

    Try your thumbnail on cheap, simplistically-designed watches. Some watch backings can be opened by prying a simple hinge in the back open. Inspect your watch to determine whether the backing will make this possible. If the backing has no screws, it can likely be opened with your thumbnail.[1]

    • This method will only work if your watch backing has no screws.
    • While you may be able to use other fingernails, your thumbnail is usually the largest and strongest.

  2. 2

    Locate your watch's hinge. On simple watches, the hinge will look like a small indentation along the edge of the watch's back. This is where you will place your thumbnail to pry off the backing.

    • Do not set your watch down as you work. Keep it in your other hand so you can maneuver it while prying it open.

    Advertisement

  3. 3

    Insert your thumbnail underneath the backing hinge and lift. As you work, your nail should face the back of the watch. Lift slowly to avoid chipping or bending your thumbnail. With pressure and patience, the backing should pop off. If the backing does not easily come off, avoid using your thumbnail so you don't damage it.[2]

    • This method is best done if you have long, healthy fingernails.

  4. 4

    Use a razor blade as an alternative. If the hinge is tight or your thumbnail is too short to pry off the backing, a flat razor blade can work as well. Place the razor blade's edge in through the hinge opening and lift until it is pried off.[3]

    • If there is no indentation but a space between the back and casing, you can use this method with a razor blade.
    • Small kitchen knives can work in a pinch if you don't have a razor blade.

    5. Advertisement

  1. 1

    Purchase a soft, mashable rubber ball. Rubber balls often have enough grip to pry off watch backings. Choose a rubberized ball that is both squishy and tacky so it can latch onto your watch's back.[4]

    • Stress balls can work as a cheaper alternative.
    • Avoid rubber balls made from hard materials. The ball needs to be soft and pliable so it can grip the backing.
    • A super-cheap alternative is to reverse-wrap a new tennis ball with duct tape until completely covered. The duct tape adhesive is very sticky and the tennis ball gives you something to grip onto.

  2. 2

    Place the watch down on a flat surface. Although you can hold the watch in your hand while you work, placing it on a flat surface will allow you to work more comfortably and efficiently. If your watch is expensive or fragile, set a towel down for the watch to rest on while you work.

  3. 3

    Press the ball firmly into the watch's backing. The rubber ball will need to press itself firmly against the backing, particularly the screw notches. Apply firm pressure as you move the ball against the backing so the ball can establish a strong grip.[5]

    • Apply pressure to the watch in increments to avoid accidentally damaging your watch.

  4. 4

    Twist the ball counterclockwise. Most watch models will loosen when turned counterclockwise and tighten when turned in the opposite direction. As you turn the watch, the backing's screws should loosen. Twist quickly and firmly to keep the rubber ball's grip firm on the backing.[6]

  5. 5

    Use the ball to loosen, but not remove, the backing. Once the backing is loose enough, you can use your fingers to remove it entirely. Twist the backing with your fingers in the same counterclockwise movement until it and the screws come off. Keep the backing and screws in a safe place so you do not lose them.[7]

  6. 6

    Use the rubber ball again to put the backing on afterward. You'll want to make sure to secure the backing on tightly once you have done whatever you needed to while removing it. Place the cover on your watch's back and press the rubber ball firmly against it. Turn swiftly in a clockwise motion to tighten the backing up again.[8]

    7. Advertisement

  1. 1

    Use scissors to loosen extremely tight backings. Rubber balls may not provide enough grip if your backing is screwed on tightly enough. Scissor tips are usually small enough to reach your watch's screws and twist them off as a specialized screwdriver would.

    • Choose a pair of scissors with blunt tips to avoid injuring yourself if they slip.

  2. 2

    Put the watch down on a firm, flat surface. Placing the watch on a flat surface will allow you to work safely while handling the scissors. If your watch is expensive or fragile, set a soft towel down for the watch to rest on while you take out the screws.

  3. 3

    Locate the watch's screw notches. These notches mark the locations of your screws. Open the handle of the scissors, then put one scissor tip into a screw notch as you prepare to unscrew it. Make sure you place the scissor end firmly inside the notch to avoid losing your grip as you turn it.[9]

  4. 4

    Twist the notches in a counterclockwise movement. Just as you would with the rubber ball method, turn the scissors in a counterclockwise movement to loosen each screw. Once you've removed your first screw, repeat this method on the remaining notches.[10]

    • When you're ready to put the backing on again, you will use the same method but twist in a clockwise movement.

  5. 5

    Try using a precision screwdriver as an alternative. If you can't get the hang of or would prefer not to use scissors, purchase a precision screwdriver from your local hardware store. Precision screwdrivers are usually small enough to unscrew watch backings without having to purchase specialized tools.

    6. Advertisement

Add New Question

  • Question

    How do I replace the backing cover of my watch? I pried it off with a thin bladed knife but it won't pop back together easily.

    Community Answer

    Try laying it upside down on a table and pushing down on the back evenly with a piece of wood.

  • Question

    How do I remove the back if there is no tab?

    Community Answer

    Some watches have screw-on case backs, which can usually be identified by notches cut into the case back or a coin-like edge. In this case, the proper tools are needed.

  • Question

    How do I open the back of a watch that has been smashed in too far?

    Community Answer

    In cases where the watch is damaged, you may need professional help to fix it. Contact a local jeweler or watch repair service to assess what needs to be done.

  • Question

    What do I do if I do not have that type of watch?

    Community Answer

    You need a watch opener tool set. You can buy a mediocre set on eBay for about $12, but it will work fine.

  • Question

    What do I do if I can't find any notches or indentations on the back of my watch to get the back off?

    Community Answer

    In that case, I would recommend taking your watch to a jeweler or other specialist so you don't accidentally damage it.

  • Question

    How to replace back cover?

    Community Answer

    If the back cover is damaged, replacement options will vary depending on your watch model. Contact a local jeweler or watch repair service to assess your options.

  • Question

    Should I stop my watch when I'm not using it?

    Community Answer

    I've stopped mine for a long time, and the initial battery still worked fine after a couple of years of inactivity. So I'd wager it preserves battery life by stopping it when you aren't using it, as I haven't changed the battery yet in mine.

  • Question

    How do I get the back off my Luv and Kush watch?

    Community Answer

    If there aren't any dents or notches on the watch and you cant use any of the tips above, then you would need the proper tools.

  • Question

    I have a Ninja Turtle watch from 2014, and I can't see any notches or anything that would help me pry it off. Does this watch need proper tools?

    Community Answer

    It is likely a pressure fit back. If so, this will require some sort of case back opening tool. Also, you could try to use methods described in this page.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

  • Be careful when handling sharp knives or screwdrivers to avoid hurting yourself.

  • If you've tried each method and you still can't get the backing open, visit a local jeweler to determine what your best option is.

Thanks for submitting a tip for review!

Advertisement

Things You'll Need

  • Blunt scissors
  • Rubberized ball
  • Duct tape and tennis ball
  • Razor blade (optional)
  • Precision screwdriver (optional)
  • Towel (optional)

About This Article

Article Summary X

If you need to pry off a watch backing but don't have the proper tools, start by turning your watch over and locating the small indentation along the edge, which is the hinge. Next, insert the edge of a razor blade or kitchen knife into the hinge opening, working slowly so you don't damage the watch. Then, lift the razor blade like a lever and apply even pressure to pry off the backing. For tips on how to pry off a particularly tight watch backing using a pair of scissors, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 1,687,616 times.

Did this article help you?

gillisonnevency99.blogspot.com

Source: https://www.wikihow.com/Pry-off-a-Watch-Backing-Without-Proper-Tools